 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Ordering number : EN6041 Thick-Film Hybrid IC STK672-110 Unipolar Fixed-Current Chopper (Self-Excited PWM) Scheme and Built-in Phase Signal Distribution IC Two-Phase Stepping Motor Driver (Square Wave Drive) Output Current: 1.8 A Overview The STK672-110 is a unipolar fixed-current chopper type 2-phase stepping motor driver hybrid IC. It features power MOSFETs in the output stage and a built-in phase signal distribution IC. The incorporation of a phase distribution IC allows the STK672-110 to control the speed of the motor based on the frequency of an external input clock signal. It supports two types of excitation for motor control: 2-phase excitation and 1-2 phase excitation. It also provides a function for switching the motor direction. Applications * Two-phase stepping motor drive in send/receive facsimile units * Paper feed in copiers, industrial robots, and other applications that require 2-phase stepping motor drive * All inputs are Schmitt inputs and 40-k (typical: -50 to +100%) pull-up resistors are built in. * The motor current can be set by changing the Vref pin voltage. Since a 0.22- current detection resistor is built in, a current of 1 A is set for each 0.22 V of applied voltage. * The input frequency range for the clock signal used for motor speed control is 0 to 25 kHz. * Supply voltage ranges: VCC1 = 10 to 42 V, VCC2 = 5.0 V 5% * This IC supports motor operating currents of up to 1.8 A at Tc = 105C, and of up to 2.65 A at Tc = 25C. Package Dimensions unit: mm 4168 [STK672-110] Features * The motor speed can be controlled by the frequency of an external clock signal (the CLOCK pin signal). * The excitation type is switched according to the state (low or high) of the MODE pin. The mode is set to 2-phase or 1-2 phase excitation on the rising edge of the clock signal. * A motor direction switching pin (the CWB pin) is provided. 32.5 8.5 26.0 1 2.0 11x2=22 Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 12799RM (OT) No. 6041-1/9 4.0 12 0.5 1.0 0.4 2.9 STK672-110 Specifications Maximum Rating at Ta = 25C Parameter Maximum supply voltage 1 Maximum supply voltage 2 Input voltage Output current Repeated avalanche capacity Allowable power dissipation Operating substrate temperature Junction temperature Storage temperature Symbol VCC max VDD max VIN max IOH max Ear max Pd max Tc max Tj max Tstg With an arbitrarily large heat sink. Per MOSFET No signal No signal Logic input pins VDD = 5 V, CLOCK 200 Hz Conditions Ratings 52 -0.3 to +7.0 -0.3 to +7.0 2.65 28 6.5 105 150 -40 to +125 Unit V V V A mJ W C C C Allowable Operating Ranges at Ta = 25C Parameter Maximum supply voltage 1 Maximum supply voltage 2 Input voltage Phase current 1 Phase current 2 Clock frequency Phase driver withstand voltage Symbol VCC VDD VIH IOH1 IOH2 fCL VDSS Tc = 105C, CLOCK 200 Hz Tc = 80C, CLOCK 200 Hz See the motor current (IOH) derating curve Minimum pulse width: 20 s ID = 1 mA (Tc = 25C) With signals applied With signals applied Conditions Ratings 10 to 42 5.0 5% 0 to VDD 1.8 2.1 0 to 25 100 min Unit V V V A A kHz V Electrical Characteristics at Ta = 25C, VCC = 24 V, VDD = 5 V Parameter VDD supply current Output current FET diode forward voltage Output saturation voltage High-level input voltage Low-level input voltage Input current Vref input voltage Vref input bias current Note: A fixed-voltage power supply must be used. Symbol ICCO Ioave Vdf Vsat VIH VIL IIL VrH IIB CLOCK = GND With R/L = 3 /3.8 mH in each phase Vref = 0.176 V If = 1 A (RL = 23 ) RL = 23 Pins 6 to 9 (4 pins) Pins 6 to 9 (4 pins) With pins 6 to 9 at the ground level. Pull-up resistance: 40 k (typical) Pin 12 With pin 12 at 1 V 62 0 50 125 4.0 1.0 250 3.5 500 0.41 Conditions Ratings min typ 2.6 0.45 1.2 0.73 max 6 0.50 1.8 1.02 Unit mA A V V V V A V nA No. 6041-2/9 Internal Equivalent Circuit Block Diagram Excitation mode selection Phase excitation signal generation Phase advance counter STK672-110 Chopping circuit Off time setting No. 6041-3/9 STK672-110 Sample Application Circuit Two-phase stepping motor At least 100 F * To minimize noise in the 5-V system, locate the ground side of capacitor CO2 in the above circuit as close as possible to pin 1 of the IC. * Insert resistor RO3 (47 to 100 ) so that the discharge energy from capacitor CO4 is not directly applied to the CMOS IC in this hybrid device. If the diode D1 has Vf characteristics with Vf less than or equal to 0.6 V (when If = 0.1 A), this will be smaller than the CMOS IC input pin diode Vf. If this is the case RO3 may be replaced with a short without problem. * Standard or HC type input levels are used for the pin 7, 8, and 9 inputs. * If open-collector type circuits are used for the pin 7, 8, and 9 inputs, these circuit will be in the high-impedance state for high level inputs. As a result, chopping circuit noise may cause the input circuits to operate incorrectly. To prevent incorrect operation due to such noise, capacitors with values between 470 and 1000 pF must be connected between pins 7 and 11, 8 and 11, and 9 and 11. (A capacitor with a value between 470 and 1000 pF must be connected between pins 6 and 11 as well if an open-collector output IC is used for the RESETB pin (pin 6) input.) * Taking the input bias current (IIB) characteristics into account, the resistor RO1 must not exceed 100 k. * The following circuit (for a lowered current of over 0.2 A) is recommended if the application needs to temporarily lower the motor current. Here, a value of close to 100 k must be used for resistor RO1 to make the transistor output saturation voltage as low as possible. Input Pin Functions (CMOS input levels) Pin CLOCK MODE CWB RESETB Pin No. 9 8 7 6 Function Reference clock for motor phase current switching Excitation mode selection Motor direction switching System reset and A, AB, B, and BB outputs cutoff. Applications must apply a reset signal for at least 20 s when power is first applied. Input conditions when operating Operates on the rising edge of the signal Low: 2-phase excitation High: 1-2 phase excitation Low: CW (forward) High: CCW (reverse) A reset is applied by a low level * A simple reset function is formed from D1, CO4, and RO3 in this application circuit. With the CLOCK input held low, when the 5-V supply voltage is brought up a reset is applied if the motor output phases A and BB are driven. If the 5-V supply voltage rise time is slow (over 50 ms), the motor output phases A and BB may not be driven. Increase the value of the capacitor CO4 and check circuit operation again. * See the timing chart for the concrete details on circuit operation. No. 6041-4/9 STK672-110 Usage Notes * 5-V system input pins [RESETB and CLOCK (Input signal timing when power is first applied)] As shown in the timing chart, a RESETB signal input is required by the driver to operate with the timing in which the F1 gate is turned on first. The RESETB signal timing must be set up to have a width of at least 20 s, as shown below. The capacitor CO4 and the resistor RO3 in the application circuit form simple reset circuit that uses the RC time constant rising time. However, when designing the RESETB input based on CMOS levels, the application must have the timing shown in figure 1. Rise of the 5-V supply voltage RESETB signal input At least 20 s CLOCK signal At least 10 s Figure 1 RESETB and CLOCK Signals Input Timing See the timing chart for details on the CLOCK, MODE, CWB, and other input pins. [Vref Figure 2 Motor Current IO Flowing into the Driver IC IOH = Vref / Rs Here, Rs is hybrid IC internal current detection resistor Vref = (R02 / (R01 + R02)) x 5 V STK672-110 : Rs = 0.22 * Allowable motor current operating range The motor current (IO) must be held within the range corresponding to the area under the curve shown in figure 4. For example, if the operating substrate temperature Tc is 105C, then IO must be held under IO max = 1.8 A, and in hold mode IO must be held under IO max = 1.5 A. No. 6041-5/9 STK672-110 * Thermal design [Operating range in which a heat sink is not used] The STK672-110 package has a structure that uses no screws, and is recommended for use without a heat sink. This section discusses the safe operating range when no heat sink is used. In the maximum ratings specifications, Tcmax is specified to be 105C, and when mounted in an actual end product system, the Tcmax value must never be exceeded during operation. Tc can be expressed by formula (A) below, and thus the range for Tc must be stipulated so that Tc is always under 105C. Tc = Ta + Tc (A) Ta: Hybrid IC ambient temperature, Tc: Temperature increase across the aluminum substrate As shown in figure 6, the value of Tc increases as the hybrid IC internal average power dissipation PD increases. As shown in figure 5, PD increases with the motor current. Here we describe the actual PD calculation using the example shown in the motor current timing chart in figure 3. Since there are periods when current flows and periods when the current is off during actual motor operation, PD cannot be determined from the data presented in figure 5. Therefore, we calculate PD assuming that actual motor operation consists of repetitions of the operation shown in figure 3. Motor phase current (sink side) Figure 3 Motor Current Timing T1: Motor rotation operation time T2: Motor hold operation time T3: Motor current off time T2 may be reduced, depending on the application. T0: Single repeated motor operating cycle IO1 and IO2: Motor current peak values Due to the structure of motor windings, the phase current is a positive and negative current with a pulse form. Note that figure 3 presents the concepts here, and that the on/off duty of the actual signals will differ. The hybrid IC internal average power dissipation PD can be calculated from the following formula. PD = (T1 x P1 + T2 x P2 + T3) / T0 (I) (Here, P1 is the PD for IO1 and P2 is the PD for IO2) If the value calculated in formula (I) above is under 1.4 W, then from figure 6 we see that operation is allowed up to an ambient temperature Ta of 60C. While the operating range when a heat sink is not used can be determined from formula (I) above, figure 5 is merely a single example of one operating mode for a single motor. For example, while figure 5 shows a 2-phase excitation motor, if 1-2 phase excitation is used with a 500-Hz clock frequency, the drive will be turned off for 25% of the time and the dissipation PD will be reduced to 75% of that in figure 5. It is extremely difficult for Sanyo to calculate the internal average power dissipation PD for all possible end product conditions. After performing the above rough calculations, always install the hybrid IC in an actual end product and verify that the substrate temperature Tc does not rise above 105C. No. 6041-6/9 STK672-110 Timing Chart 2-phase excitation Gate F1 Gate F2 Gate F3 Gate F4 1-2 phase excitation Gate F1 Gate F2 Gate F3 Gate F4 No. 6041-7/9 STK672-110 1-2 phase excitation (CWB) Gate F1 Gate F2 Gate F3 Gate F4 Switching from 2-phase to 1-2 phase excitation Gate F1 Gate F2 Gate F3 Gate F4 No. 6041-8/9 STK672-110 Figure 4 Operating region when fCL 200 Hz Figure 5 Motor: Hybrid IC internal average power dissipation, PD -- W Motor current, IOH -- A Continuous 2-phase excitation operation Motor used:R = 0.63 L = 0.62 mH The data are typical values. Operating region in hold mode Operating Substrate Temperature, TC -- C Figure 6 With no heat sink, the IC vertical, and convection cooling Motor current, IOH -- A Substrate temperature rise, TC -- C Hybrid IC internal average power disspation, PD -- W Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of January 1999. Specifications and information herein are subject to change without notice. PS No. 6041-9/9 |
Price & Availability of STK672-110
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |